百怡富科技有限公司 » 打印機 » > SPRT 打印機其他方面問題


2021-2-17 15:06 pericles
> SPRT 打印機其他方面問題

以下為 SPRT 打印機其他問題, 包括:

1.  新版 SPRT POS887 打印機 (橙色鍵) 蓋關不到
2.  SPRT POS887/890 打印機的蜂鳴器設置 (1/2) - 拆除 及 網絡制式設置靜音
3.  SPRT 印表機如何設置 Logo
4.  SPRT Printer Logo Setting (English)
5.  SPRT 打印機設置為打印時彈櫃 (開始及結束)
6.  SPRT 打印出花畫面或出白紙解決方法
7.  機蓋關不到, 將熱感紙拿走, 機蓋還是關不到
8.  印表機有紙出, 但沒有文字
9.  網絡打印機出吾到紙
10. SPRT POS887/890 打印機的蜂鳴器設置 (2/2) -  USB 制式設置靜音

2021-2-17 15:07 pericles
1. 新版 SPRT 蓋關不到解決方法

取下兩個彈簧,將蓋裝番上去。

[img]http://www.pericles.net/download/seven/printer.jpg[/img]

2021-2-17 15:09 pericles
SPRT POS887 打印機的蜂鳴器設置

[size=5]POS887中有兩個蜂鳴器。
大蜂鳴器:
1.首先將以下螺絲拿出來
[img]http://www.pericles.net/ftp1/support1/POS887/PrinterBuzzerCut1.JPG[/img]
2.拿起外殼後,將以下螺絲拿出來(有可能沒有此板,故可以跳過此步驟)
[img]http://www.pericles.net/ftp1/support1/POS887/PrinterBuzzerCut2.JPG[/img]
3.將以下的電線拆出來,那麼大蜂鳴器就會停止運作。
[img]http://www.pericles.net/ftp1/support1/POS887/PrinterBuzzerCut3.JPG[/img]

小蜂鳴器
1.首先下載以下程式:[url=http://www.pericles.net/ftp1/support1/POS887/SettingToolV3.58_1.7.exe]POS88Setting[/url]
2.下載完成後,執行以下程式
[img]http://www.pericles.net/ftp1/support1/POS887/PrinterBuzzerCut4.JPG[/img]
3.選擇適當的打印機及適當的接口後(USB/NET),就將蜂鳴器禁止,最後按下SET。
[img]http://www.pericles.net/ftp1/support1/POS887/PrinterBuzzerCut5.JPG[/img][/size]

2021-2-17 15:11 pericles
3. SPRT 印表機如何設置Logo

SPRT 型號: SP-POS-88VEF 發票打印機如何設置Logo 的操作圖
[img]http://www.pericles.net/download/seven/printer_logo.jpg[/img]

2021-2-17 15:15 pericles
4. SPRT Printer Logo Setting (English)

[b][size=5][color=Red]型號一: SPRT Printer[/color][/size][/b]

步驟:
1.首先將Logo 放在[color=Red]300像素中間的尺寸內[/color],保存為[color=Red]單色位圖bmp[/color] 的格式, 存檔在[color=Red]C盤內的圖片位置內[/color]
2.在前台左下角系統維護,點擊"設置"進入收銀機設置內
3.印表機類型選擇--->SP-POS88---->圖片路徑請選擇番步驟1保存的bmp 格式的位置圖片, 選擇確實後保存即可.

[b][size=5][color=Red]Moudle 1: SPRT Printer[/color][/size][/b]
Step1: Save the Logo siza [color=Red]in the middle of the 300 pixels[/color], colors: 2 colors (1-bit) save to [color=Red]C:\Users\Pictures\Logo.bmp[/color],
          Save type is [color=Red]BMP- Windows Bitmap (*.bmp)[/color].
Step2: Open the Cashier, click the Maintenance, and then click the Cashier Setting from the Setting.
Step3: choose the SP-POS88 from the Cashdrawer Type, open the bmp file from the Image Path, finally save it finish.

[img]http://www.pericles.net/download/seven/printer_logo.jpg[/img]

2021-2-17 15:18 pericles
5. SPRT 打印機設置為打印時彈櫃 (開始及結束)

[size=5]首先1.進入控制台
       2.檢視裝置和打印機
       3.選擇80mm Series Printer 右鍵 列印喜好設定
       4.選擇 no drawer[/size]
[img]http://www.pericles.net/ftp1/support1/Control Panel.JPG[/img]
[img]http://www.pericles.net/ftp1/support1/printer setting.JPG[/img]

2021-2-17 15:20 pericles
6. SPRT打印出花畫面或出白紙解決方法

[size=5]因為底板部份部件接觸不良,令到資料不能準確打印出來,故可用以下方法解決:[/size]
Because the parts of the bottom plate contact is bad, so that the data can not be accurately printed out, it can be solved by the following methods:
[size=5]1.首先將底部的四粒螺絲拆出來(紅圈),及將底部移出來[/size]
1. first remove the four screws at the bottom (red circle) and move the bottom out
[img]http://www.pericles.net/ftp1/support1/SPRTError3.JPG[/img]
[size=5]2.然後將紅圈內的部件移回直立狀態(或有可能有垃圾在紅圈內的金屬片旁,請清走電路板上的垃圾)[/size]
2. then move the components in the red loop back to the upright state
[img]http://www.pericles.net/ftp1/support1/SPRTSPRTError.JPG[/img]
[img]http://www.pericles.net/ftp1/support1/SPRSPRTError2.JPG[/img]
[size=5]3.最後將打印機回復原狀[/size]
3. finally revert the printer back to its original state
[size=5]PS:如果直立後也出花畫面或白紙,只要將紅圈內的部件作用適當的微調,就可以成功解決問題[/size]
PS: if it is upright, it will also produce a picture or white paper. As long as the function of the components in the red circle is properly adjusted, the problem can be solved successfully
[color=Red]新版印機機 POS887E 位置, 需要擺直 :[/color]
[img]http://www.pericles.net/download/seven/new_pos887E.jpg[/img]



下面是這種情況而打印出來的收據和自檢的樣品
Below is the samples of receipt and the self-check       
        [img]http://www.pericles.net/ftp1/may/support/8f9af75c-c13f-48c5-a733-06f33dc1a02b.jpg[/img]
        [img]http://www.pericles.net/ftp1/may/support/7d39c99e-9bcd-43f2-b72a-aed7d576e33f.jpg[/img]

2021-2-17 17:23 pericles
7. 機蓋關不到, 將熱感紙拿走, 機蓋還是關不到

[b][size=4]原因...  [/size][/b]
是 機蓋被切刀頂著, 打開前蓋, 向前或向後推動滖輪進行調節便可
[img]http://www.pericles.net/ftp1/eddy/Printer_Cover.jpg[/img]

2021-2-17 17:24 pericles
8. 印表機有紙出, 但沒有文字

[b][size=4]常見原因有3個...  [/size][/b]
1. 有可能用錯非熱感紙
2. 熱感紙底面倒轉了安放
3. 收據/廚房印表機的打印頭被某些東西擋著了

[b][size=4][color=Blue]解決方法:[/color][/size][/b]
1. 打開機蓋, 看看有沒有紙碎, 請徐去
2. 打開機蓋, 用布沾上少量稀釋了的清潔上劑或火酒, 為打印頭清潔.
    ** 留意 ** 此為電器用品, 忌水.
   
    [color=Blue][size=3]清潔打印頭位置:[/size][/color]
    [img]http://www.pericles.net/ftp1/eddy/Printer_Head.jpg[/img]

2021-2-17 17:25 pericles
9. 網絡打印機出吾到紙

步驟一:檢查打印機是否離線狀態
[img]http://www.pericles.net/download/seven/20160701.jpg[/img]

步驟二: 檢查網絡問題
[img]http://www.pericles.net/download/seven/20160702.jpg[/img]

2023-10-28 11:26 pericles
10. SPRT POS887/890 打印機的蜂鳴器設置 (2/2) - USB 制式設置靜音

1> 下載及執行 SettingToolV3.58_5.1
     Zip File:  [url]http://www.pericles.net/ftp1/Driver/SettingToolV3.58_5.1.zip[/url]
     Exe File:  [url]http://www.pericles.net/ftp1/Driver/SettingToolV3.58_5.1.exe[/url]

2> 依照以下圖片, 連接及設置 USB SPRT 打印機
     [img]http://www.pericles.net/ftp1/Driver/SPRT-887-890.jpg[/img]

頁: [1]


Powered by Discuz! Archiver 5.0.0  © 2001-2006 Comsenz Inc.