Board logo

標題: > SPRT 打印機其他方面問題 [打印本頁]

作者: pericles    時間: 2021-2-17 15:06     標題: > SPRT 打印機其他方面問題

以下為 SPRT 打印機其他問題, 包括:

1.  新版 SPRT POS887 打印機 (橙色鍵) 蓋關不到
2.  SPRT POS887/890 打印機的蜂鳴器設置 (1/2) - 拆除 及 網絡制式設置靜音
3.  SPRT 印表機如何設置 Logo
4.  SPRT Printer Logo Setting (English)
5.  SPRT 打印機設置為打印時彈櫃 (開始及結束)
6.  SPRT 打印出花畫面或出白紙解決方法
7.  機蓋關不到, 將熱感紙拿走, 機蓋還是關不到
8.  印表機有紙出, 但沒有文字
9.  網絡打印機出吾到紙
10. SPRT POS887/890 打印機的蜂鳴器設置 (2/2) -  USB 制式設置靜音
作者: pericles    時間: 2021-2-17 15:07     標題: 1. 新版 SPRT 蓋關不到解決方法

取下兩個彈簧,將蓋裝番上去。


作者: pericles    時間: 2021-2-17 15:09     標題: SPRT POS887 打印機的蜂鳴器設置

POS887中有兩個蜂鳴器。
大蜂鳴器:
1.首先將以下螺絲拿出來

2.拿起外殼後,將以下螺絲拿出來(有可能沒有此板,故可以跳過此步驟)

3.將以下的電線拆出來,那麼大蜂鳴器就會停止運作。


小蜂鳴器
1.首先下載以下程式:POS88Setting
2.下載完成後,執行以下程式

3.選擇適當的打印機及適當的接口後(USB/NET),就將蜂鳴器禁止,最後按下SET。

作者: pericles    時間: 2021-2-17 15:11     標題: 3. SPRT 印表機如何設置Logo

SPRT 型號: SP-POS-88VEF 發票打印機如何設置Logo 的操作圖

作者: pericles    時間: 2021-2-17 15:15     標題: 4. SPRT Printer Logo Setting (English)

型號一: SPRT Printer

步驟:
1.首先將Logo 放在300像素中間的尺寸內,保存為單色位圖bmp 的格式, 存檔在C盤內的圖片位置內
2.在前台左下角系統維護,點擊"設置"進入收銀機設置內
3.印表機類型選擇--->SP-POS88---->圖片路徑請選擇番步驟1保存的bmp 格式的位置圖片, 選擇確實後保存即可.

Moudle 1: SPRT Printer
Step1: Save the Logo siza in the middle of the 300 pixels, colors: 2 colors (1-bit) save to C:\Users\Pictures\Logo.bmp,
          Save type is BMP- Windows Bitmap (*.bmp).
Step2: Open the Cashier, click the Maintenance, and then click the Cashier Setting from the Setting.
Step3: choose the SP-POS88 from the Cashdrawer Type, open the bmp file from the Image Path, finally save it finish.


作者: pericles    時間: 2021-2-17 15:18     標題: 5. SPRT 打印機設置為打印時彈櫃 (開始及結束)

首先1.進入控制台
       2.檢視裝置和打印機
       3.選擇80mm Series Printer 右鍵 列印喜好設定
       4.選擇 no drawer



作者: pericles    時間: 2021-2-17 15:20     標題: 6. SPRT打印出花畫面或出白紙解決方法

因為底板部份部件接觸不良,令到資料不能準確打印出來,故可用以下方法解決:
Because the parts of the bottom plate contact is bad, so that the data can not be accurately printed out, it can be solved by the following methods:
1.首先將底部的四粒螺絲拆出來(紅圈),及將底部移出來
1. first remove the four screws at the bottom (red circle) and move the bottom out

2.然後將紅圈內的部件移回直立狀態(或有可能有垃圾在紅圈內的金屬片旁,請清走電路板上的垃圾)
2. then move the components in the red loop back to the upright state


3.最後將打印機回復原狀
3. finally revert the printer back to its original state
PS:如果直立後也出花畫面或白紙,只要將紅圈內的部件作用適當的微調,就可以成功解決問題
PS: if it is upright, it will also produce a picture or white paper. As long as the function of the components in the red circle is properly adjusted, the problem can be solved successfully
新版印機機 POS887E 位置, 需要擺直 :




下面是這種情況而打印出來的收據和自檢的樣品
Below is the samples of receipt and the self-check       
       
       
作者: pericles    時間: 2021-2-17 17:23     標題: 7. 機蓋關不到, 將熱感紙拿走, 機蓋還是關不到

原因...  
是 機蓋被切刀頂著, 打開前蓋, 向前或向後推動滖輪進行調節便可

作者: pericles    時間: 2021-2-17 17:24     標題: 8. 印表機有紙出, 但沒有文字

常見原因有3個...  
1. 有可能用錯非熱感紙
2. 熱感紙底面倒轉了安放
3. 收據/廚房印表機的打印頭被某些東西擋著了

解決方法:
1. 打開機蓋, 看看有沒有紙碎, 請徐去
2. 打開機蓋, 用布沾上少量稀釋了的清潔上劑或火酒, 為打印頭清潔.
    ** 留意 ** 此為電器用品, 忌水.
   
    清潔打印頭位置:
   
作者: pericles    時間: 2021-2-17 17:25     標題: 9. 網絡打印機出吾到紙

步驟一:檢查打印機是否離線狀態


步驟二: 檢查網絡問題

作者: pericles    時間: 2023-10-28 11:26     標題: 10. SPRT POS887/890 打印機的蜂鳴器設置 (2/2) - USB 制式設置靜音

1> 下載及執行 SettingToolV3.58_5.1
     Zip File:  http://www.pericles.net/ftp1/Driver/SettingToolV3.58_5.1.zip
     Exe File:  http://www.pericles.net/ftp1/Driver/SettingToolV3.58_5.1.exe

2> 依照以下圖片, 連接及設置 USB SPRT 打印機
     




歡迎光臨 百怡富科技有限公司 (http://www.pericles.net/bbs/) Powered by Discuz! 5.0.0